You can replace Corsair HS60 ear pads by carefully removing the old pads, then aligning and fitting the replacements. If a pad will not release or seat smoothly, stop rather than forcing it; a little patience is safer than stressing the attachment.
Take your time as you work, especially if a worn pad catches or a new one feels uneven as you position it. For example, if one side resists while the other moves freely, pause and check the fit instead of pushing harder. This walkthrough focuses on the removal and fitting process, with simple precautions to help you avoid damage while refreshing your headset.
What to prepare before removing a pad
Before you remove a pad, confirm the replacements are labeled for the Corsair HS60 and check how the existing cushion attaches. A listing that names the HS60 is a useful compatibility check; some replacement pads are sold for the HS50, HS60, and HS70 together, so read the model list rather than relying on a similar-looking headset. [1]
Set the headset on a stable, clear surface where the earcups can rest without being squeezed. Keep the cable free of the work area, and move the headset by its frame or earcup rather than tugging on the cord; this gives you a steadier setup and helps avoid putting strain on parts you are not replacing.
Take a moment to inspect the edge of the old pad where it meets the earcup. Look for the attachment seam and note whether the cushion seems to pull out of a socket or uses a different fitting, before putting pressure on it. Corsair’s instructions describe pulling the pad out of the headset socket and aligning the new one with that socket, so checking the join first can help you understand what you are handling. [2]
Keep the replacement pads and headset within easy reach, and make sure you have enough light to see the attachment edge. If the old pad partly covers the join, gently shift the cushion fabric aside to inspect it without beginning the removal yet.
How to remove the old ear pads
Work on one earcup at a time. Hold the earcup steady while you remove its pad, so you can focus on the attachment instead of wrestling with both sides. Start on whichever side is easier to reach, and leave the other pad in place until you finish.
Grip the pad from its inner edge. Reach into the opening and hold the cushion close to where it meets the headset; pull the pad out of the socket. [2] Keep your grip on the pad itself, rather than the outer rim of the earcup. If the cushion shifts but stays attached, adjust your hold nearer the inner edge and try the release motion again.
Check for a twist-fit before pulling further. Some designs use a rotating attachment, so follow its release direction rather than pulling against the lock. For Corsair Virtuoso and newer HS series headsets, Corsair instructs you to rotate the current earpad clockwise before removing it. [3] If your pad does not appear to use that mechanism, use the inner-edge pull described above instead of assuming it needs a twist.
How to fit the replacement pads
Hold the replacement pad over the earcup and line it up with the headset socket before pressing. Check that the cushion’s edge follows the socket all the way around; if one side is offset, pause and reposition it rather than pushing that section in first. [2]
Press the pad into place a little at a time, moving around the attachment evenly. For example, work from one edge to the opposite edge, then continue around the remaining sides so the cushion settles into the socket without one section bearing all the pressure.
Once the pad is seated, look around its full edge and check that it sits evenly against the earcup. Give it a light touch to confirm it feels secure, then fit the replacement on the other earcup the same way. [2]
Mistakes that can damage the headset
Avoid damaging your HS60 by using light pressure and stopping when anything looks wrong. The cushion should not need a hard yank, and the earcup should not be used as a lever; if you feel yourself pulling hard, pause and reassess rather than risking damage. [2]
A replacement that sits crooked is a cue to stop, not press harder. Take it back off and realign it with the socket before trying again; forcing a misaligned pad can put stress on the attachment. [2]
Stop if the attachment looks damaged
Check the socket and the pad’s attachment as you work. If either looks cracked, bent, or otherwise damaged, stop instead of continuing to pry or press; further handling could make the problem worse. [3]
For example, if an edge seems to catch but the rest of the pad will not move, do not twist the earcup or wedge a tool into the gap. Set the headset aside and inspect the attachment in good light before deciding whether it is safe to continue. That pause is better than turning a small fitting issue into a damaged socket.
Check the fit before using the headset
Before using the headset, check that both ear pads sit evenly and stay attached with gentle handling. Look around each earcup: the cushions should appear similarly positioned, with no edge lifting away from the socket. Corsair’s replacement guidance describes aligning the new pads with the headset socket, so a visible gap or uneven edge is a reason to pause and inspect the fit. [2]
Handle the headset lightly while checking; you do not need to tug on the pads to test them. If one shifts with gentle contact, or you can see part of its edge pulling free, take another look at the alignment before wearing the headset. A quick visual check on both sides can catch a loose fit before it becomes distracting during a game.
If a pad will not fit, recheck its alignment and confirm that its attachment matches the HS60. Corsair’s instructions say to align replacement pads with the headset socket. [2] If you still cannot get the pad to sit securely, stop rather than forcing it; check the pad’s fit information or choose a replacement intended for the HS60 before trying again.